Avid Complete Production Toolkit Especificaciones Pagina 37
- Pagina / 119
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Complete Production Toolkit 2 Guide32
AutoJoin Indicator
After a Latch automation pass with AutoJoin en-
abled, the AutoJoin indicator appears in the
Pro Tools Edit window.
The AutoJoin indicator is a vertical line that sig-
nifies the point where the last automation pass
was stopped, and the point where the “join” will
automatically occur on all tracks that were writ-
ing during that previous pass. When automa-
tion writing is resumed from this point, the line
disappears.
Touch/Latch Mode
Touch/Latch Automation mode places a track’s
Volume control in Touch mode and all other au-
tomatable controls in Latch mode.
In Touch/Latch mode, the Volume control fol-
lows Touch behavior, writing automation when
touched and returning to previously written lev-
els when released.
All other controls follow Latch behavior, writing
automation when touched and continuing until
playback stops, or until you punch out of writ-
ing automation.
AutoJoin indicator in the Edit window
To use Join or AutoJoin to resume writing on
controls that were writing when the trans-
port stopped, restart the transport before the
AutoJoin indicator.
AutoJoin indicator
Selecting Touch/Latch mode
- Complete Production Toolkit 2 1
- Legal Notices 2
- Documentation Feedback 2
- Contents iii 3
- Contents v 5
- Introduction 6
- Additional Software 7
- System Requirements and 8
- Compatibility 8
- Registration 8
- Conventions Used in This 8
- About www.avid.com 9
- Installing Complete 10
- Production 2 Toolkit 10
- Authorizing Complete 11
- Production Toolkit 2 11
- Uninstalling Complete 12
- Option and Included Plug-Ins 12
- Session and Track Features 14
- VCA Master Tracks 15
- VCA Master Track Controls 16
- Record Enable 17
- Level Meter 17
- Advanced Group Dialog 18
- Mix Groups 19
- Setting Group Attributes 19
- Selecting Group Attributes 20
- Momentary Solo Latch Option 21
- Setting Playback Location 22
- Commands 22
- Play Commands 23
- Numeric Keypad Set to 24
- AutoFades 24
- Preferences 25
- Automation Section 26
- Advanced Editing Features 28
- Replacing Audio Regions 29
- Replace Region Dialog 30
- 2 Do one of the following: 31
- 4 Click OK 31
- TCE (Time Compression and 32
- Expansion) Edit To Timeline 32
- Selection 32
- Expanding Alternate Channels 33
- Advanced Automation Features 36
- AutoJoin Indicator 37
- Trim Off 38
- Read Trim 38
- Touch Trim 39
- Latch Trim 39
- Touch/Latch Trim 39
- Write Trim 39
- Composite Automation 40
- Playlist 40
- Copy Track Automation to 41
- AutoMatch 42
- Prime Controls for Writing 43
- Automation in Latch Mode 43
- AutoMatch button 44
- Glide Automation 45
- Trim Automation 47
- Suspending Trim Automation 49
- Clearing Trim Automation 49
- Automation Write to 50
- Start/End All buttons 50
- Automation Write On 51
- Stop buttons 51
- Write Automation to the Next 52
- Breakpoint or to the Punch 52
- Point and Trim Mode 54
- Guidelines for “Write To” 55
- Overwrite or Extend Mute 56
- Automation 56
- Mute on state overwritten 57
- Snapshot Automation 59
- Automation Playlists 60
- Existing Automation Data 60
- Elsewhere 61
- Preview Automation 62
- Previewing New Automation 63
- Suspending Preview Mode 64
- Punching Preview Values 64
- Preview Mode and “Write To” 64
- Isolating Multiple Controls 64
- Capture Automation 65
- Punching Captured Automation 66
- All Controls 66
- Capture and Trim Mode 67
- Capture and Preview Mode 68
- VCA Master Track Automation 69
- Coalescing VCA Automation 70
- Duplicating a Slave Track 71
- Surround Features 72
- New Sessions 73
- Multichannel I/O Setups) 73
- Custom Multichannel Paths 73
- Importing Session Data 73
- Default 5.1 Output Paths 75
- Default 5.1 Output Bus Paths 75
- Example LCRS Setup 76
- Metering 77
- Default I/O Selectors in I/O 78
- Routing Audio for Surround 79
- Multichannel Audio Tracks 80
- Changing Format 81
- Multichannel Signal Routing 82
- Multichannel send panner 83
- Mono meter 83
- Mono output format 83
- Master Faders 84
- Mono, Multi-Mono and 84
- Multichannel Plug-Ins 84
- Multi-Mono Plug-Ins 85
- Paths in Surround Mixes 86
- Example Paths and Signal 88
- Routing for a Surround Mix 88
- Submix Stem Examples 89
- Surround Mixing 89
- Multiple Output Assignments 89
- Figure 7. FX stem 90
- Figure 8. Music stem 90
- LFE and Filtering 91
- LFE fader 91
- Click and drag to pan 92
- Output Windows 93
- Surround Panner Controls 94
- X/Y grid 95
- X/Y mode icon 95
- Front/Rear Inverse 96
- Front Inverse 96
- Rear Inverse 96
- Panning Mode button 97
- 3-Knob trajectory 98
- 3-Knob mode 98
- AutoGlide Mode 99
- AutoGlide mode 100
- Snap Pan to 100
- Speaker icons 100
- Pan Location 100
- Divergence 101
- Center % (Percentage) 101
- LFE Faders in Multichannel 102
- 5.1 Format Track Layouts 103
- Video Features 104
- Support for Video Import 105
- Video Regions 105
- Basic Video Editing Features 106
- Managing Regions 107
- Chapter 7: Video Features 103 108
- Video Region Groups 109
- Browsing Video in the Video 109
- Universe Window 109
- Universe 110
- Included Plug-Ins 112
- Numerics 114
- Index 111 116
- Index 113 118
- Technical Support (USA) 119
- Product Information 119
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales